Vintage/Scale Racing Series

PRESENTING THE 2010 VINTAGE/SCALE RACING SERIES

Races will be held at:

LUCKY BOBS RACEWAY
5822 WEST FOREST HOME AVE
MILWAUKEE WI 53220
414-327-4003 BOB THELEN
www.lucky-bobs-slot-cars.com

ALPHA RACEWAY
716 NORTHWEST WAY
FOND DU LAC WI 54937
920-922-6509 PAUL PFEIFFER
www.alphaslotracing.com

REVOLUTION RACEWAY
(INSIDE HOBBYTOWN USA OSHKOSH)
807 OREGON ST.
OSHKOSH WI 54902
1-800-486-0610 JESS
www.hobbytownoshkosh.com

Schedule...

Track opens at 9:00 am on the race day.
Amateur Vintage GT tech begins at 11:00 am followed by
Expert - Vintage GT
Can Am
Retro Pro/Anglewinder
Indy Car

RACE #1...SATURDAY JANUARY 30 - ALPHA RACEWAY

RACE #2...SATURDAY APRIL 24 - LUCKY BOB'S RACEWAY

RACE #3... SATURDAY JUNE 5 - ALPHA RACEWAY

RACE #4... SATURDAY JULY 17 - ALPHA RACEWAY

RACE #5... SATURDAY SEPTEMBER 11 - REVOLUTION RACEWAY (small track)

RACE #6... SATURDAY OCTOBER 16 - ALPHA RACEWAY

There is just nothing like the ultra close, side by side racing that is almost guaranteed with these car/motor combinations! And we'll offer it up for you whether you are young, advancing your racing skills, or an old Pro.

New for 2010...

Can-Am Now is only for IRRA rules inline Can Am cars. JK Falcon 7, or Pro Slot mini motor #4002B with puppy dog arm. Find complete rules on Slotblog...
Look for Retro-D3 rules

Indy Car We use the Badgerland Indy car rules

Retro Pro/Anglewinder This class is actually for two distinct kinds of cars racing together.

1. Retro Pro D3 Anglewinders conforming to D3 Retro Pro Rules and must use Pro Slot mini motor with puppy dog arm. No ball bearings in motor.

2. Anglewinder Any stamped steel chassis. Falcon 7 or Pro Slot mini with puppy dog arm. Any gear ratio. Any vintage (Can Am recommended). .063 clearance in back, no minimum in front. Minimum car weight 100 grams.

Amateur Vintage GT and Expert GT
Now again we have identical rules.
Champion Turbo Flex Chassis, Slick 7 588 motor, 11-38 gears (must use PSE 38) Vintage FT bodies (some will be allowed a 1/4" spoiler). Clearance .063 in rear .047 in front.

Classes....

Amateur Vintage GT: For drivers who are not yet ready to "run with the big dogs" $5.00 entry fee

Expert Vintage GT: Expert class is open to all* some of the best racers in the region will compete $5.00 entry fee

Can Am: Open to all drivers... 5 races $10.00 entry fee

Retro Pro/Anglewinder: $10.00 entry fee

Indy Car: Open to all drivers...using Badgerland rules. $10.00 entry fee

Concours awards at each race!

At season end, trophies are awarded to the top finishers in each category.

1/24th Scale Amateur and Expert Vintage Rules

Chassis:     Can Am and Amateur GT Classes must use Champion Turbo Flex chassis with Steel pans. No cutting, bending, or modifying the chassis except… the motor mounting bracket may be removed. A "U" shaped brace may be used to reinforce the rear uprights. Pin tube body mounts may be added. May solder axle bushings to chassis uprights. Lead weights may be added. The guide tongue may be reinforced. Must use oilite bushings.

Motor:     Must use Slick 7 588 motor.

Gears:     Must use an 11-tooth straight or angle pinion. Must us a PSE 38-tooth spur.

Wheels:     Fronts must be a metal wheel with a rubber tire. Minimum .500" diameter. Any rear tires may be used but may not exceed .800" diameter.

Axle:     Must use a solid steel rear axle…. No hollow or lightweight axles allowed. Front axle must be .055" or .063" piano wire. Front axle may be soldered to the chassis and may be bent.

Clearance: Minimum .047” front and .063” (1/16) rear.

Bodies:     Scale appearing Vintage bodies from any manufacturer may be used. (GT cars are those with a top … closed cockpit). Bodies must be suitably painted, with clear windows, clear front wheel wells, have 3 numbers, and a full 3-dimensional interior.

BadgerLand INDY CLASS 2008-2009

Chassis:

STOCK/MODIFIED FLEXI TYPE.
STOCK/MODIFIED STEEL TYPE
COMPLETE SCRATCH BUILT
INLINE CHASSIS WILL BE ALLOWED (LOWEST GEAR RATIO ALLOWED IS 3.18 TO 1)
EXAMPLE: 9 TOOTH PINION WITH 30T JK #5030 GREEN GEAR EQUALS 3.33 TO 1 RATIO

ALL CHASSIS

1) CHASSIS MATERIALS:

BRASS: SHEET, ROD AND TUBE
STEEL: WIRE, PIN TUBING AND QUIDE TONGUES
STAINLESS STEEL TONGUES CUT OFF FROM CENTER SECTIONS OF FLEXI CHASSIS.
THEY CANNOT BE CUT OFF ANY FURTHER BACK THAN 3/8” BEHIND THE FRONT AXLE.
STEEL WISHBONES/GUIDES FROM EXISTING AVAILABLE STEEL CHASSIS ARE ALLOWED.
(JK, KELLY, MOSSETTI, ETC)

2) NO PART OF THE CHASSIS INCLUDING GUIDE FLAG MAY BE VISIBLE FROM A TOP VIEW.
THE ONLY EXCEPTION IS THE FRONT AXLE AND SCALE SIZED WISHBONES.

3) THE BODY MUST BE TRIMED TO THE MOLDED BODY INTENDED SHAPE OF THE CAR

4) FRONT MOUNTED GUIDE FLAG IS THE ONLY PART THAT ENTERS THE TRACK SLOT

5) MAXIMUM WIDTH OF THE CHASSIS PANS IS 2.40 INCHES.

6) HINGED PAN MOVEMENT IS ALLOWED.

7) FLOATING PIN TUBES ARE ALLOWED.

8) IF IT IS NOT COVERED, IT IS NOT LEGAL.
THE BADGERLAND SERIES HAS THE RIGHT TO DISALLOW ANY CAR AT TECH,
WHICH DOES NOT MEET THE INTENT OF THE RULES.

ANY OILITE BEARINGS ARE ALLOWED INCLUDING SLICK 7 AND OFFSET BEARINGS. (NOTE: REAR TIRE SIZE REQUIREMENTS)
REAR UPRIGHT MAY BE REINFORCED USING “U” SHAPED PIANO WIRE OR SLICK 7’S S7-390 BRACE..
MOTOR BRACE MAY BE TRIMMED DOWN OR REMOVED.
FLOATING PIN TUBES ARE ALLOWED.
LEAD WEIGHT MAY BE ADDED.
.047 CLEARANCE AT REAR INCLUDING GEAR. (FRONT NO TECH)

NOTE: THE RACE DIRECTOR WILL BLACK FLAG ANY CAR DRAGGING ON THE TRACK.

Motors

STOCK JK FALCON 7, TSR-D3 AND PROSLOT MINI PS-4002 OR PS-4002B WITH PUPPY DOG ARM (ONE MOTOR PER RACE)

GEARS/AXLES/WHEELS

64 PITCH GEARS ONLY.
MUST USE 11 TOOTH PINION (ANGLE OR STRAIGHT ALLOWED)
64 PITCH SPUR GEARS 35-39 TEETH ALLOWED.
SEE GEAR RULE FOR INLINE CARS ABOVE UNDER CHASSIS RULES
3/32 (.09375) REAR AXLES.
SOLID STEEL AXLES ONLY. (NO HOLLOW OR LIGHT WEIGHT MATERIALS ALLOWED)
FRONT AXLE MAY BE SOLDERED TO THE CHASSIS.
FRONT WHEELS MAY ROTATE INDEPENDENTLY.
FRONT WHEELS MUST TOUCH AND ROLL IN THE CORNERS.
FRONT WHEELS ARE .620 MIN. DIAMETER AND .250 MIN. WIDTH.
FRONT WHEELS MUST HAVE METALLIC HUBS AND BLACK TIRE MATERIAL.
REAR WHEELS MUST BE BLACK WITH .750 MINIMUM AND .790 MAXIMUM DIAMETERS.
REAR TIRES WILL HAVE A MAXIMUM WIDTH OF .810”.

LEAD WIRES

LEAD WIRES MAY BE CHANGED.
MAGNET WIRE OR MAGNET TYPE WIRE IS NOT ALLOWED.
GUIDE CLIPS ARE ALLOWED.

INDYCAR BODIES

MAXIMUM REAR WING HEIGHT 1-5/8” ON TECH BLOCK
THE BODY MUST BE TRIMMED TO THE MOLDED BODY CUT LINES
RED FOX: INDY OR F1 BODIES
JK BODY LIST:

F1 WILLIAMS JK6108
F1 FERRARI JK6104
F1 MCLAREN JK6105
F1 JAGUAR JK6107
LOLA JK7006
BENNETON JK7004
MARCH-INDY JK7005
FERRARI JK6102
JRL INDY JK6101BD
LOLA-CHAMP CAR JK6115
REYNARD-CHAMP CAR JK6116
G FORCE-IRL JK6118
DALLARA-IRL JK6119
JRL INDY JKP610011 EXT REAR WING

Return to Alpha Home